MAXTECH CORPORATION XPV 336ER (DSF1133V/R16-PNP) Card Type Modem, Fax Chip Set Unidentified I/O Options Line in, line out, microphone in, speaker out, serial port (RS-232), DC power Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus External [Image] CONNECTIONS Function Label Function Label Line out CN1 Serial port CN5 Line in CN2 DC Power CN6 Microphone in CN3 Power switch SW1 Speaker out CN4 DIAGNOSTIC LED(S) LED Color Status Condition TST Unidentified Blinking Modem is either in test mode or is resending data TST Unidentified Off Modem is not in test mode or resending data HS Unidentified On Communicating at 2400bps or above HS Unidentified Off High speed transmission is disabled AA Unidentified On Auto-answer is enabled AA Unidentified Blinking Ring is detected AA Unidentified Off No line activity detected CD Unidentified On The modem detects carrier signal from remote modem CD Unidentified Off The modem cannot detect carrier signal from remote modem OH Unidentified On Modem is preparing to dial OH Unidentified Off Modem is not dialing RD Unidentified On Data is being sent to the computer via the modem RD Unidentified Off Data is not being sent from the modem to the computer SD Unidentified On Data is being received by the modem via the computer SD Unidentified Off The modem is not receiving data from the computer TR Unidentified On Modem is ready to receive commands TR Unidentified Off Modem is not ready to receive commands MR Unidentified On Modem is turned on MR Unidentified Off Modem is turned off SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &F, &P, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \K, \N %C, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands +MS, -SMS=X,Y,Z,T, -SSE=x, -SQS=X,Y Voice Commands #BDR, #CID, #CLS, #MDL?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSDB, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTOSCAN MODE Type: Immediate Format: AT [cmds] Nn [cmds] Description: Enables/Disables Autoscan mode Command Function N0 Autoscan mode disabled í N1 Autoscan mode enabled CLEAR TO SEND CONFIGURATION Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Configures CTS settings based on the flow control settings Command Function &R0 Reserved &R1 Sets CTS operation based on flow control requirements COMMUNICATIONS MODE (ASYNCHRONOUS) Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE (DATA LINK AND FALLBACK) Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Configures data link and fallback options Command Function &Q0 Set Direct data link only í &Q5 Set V.42 data link with fallback options enabled &Q6 Set Normal data link only DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR is off while in command mode and set on in on-line mode FLOW CONTROL Type: Immediate Format: AT [cmds] &K [cmds] Description: Configures flow control settings Command Function &K0 Flow control disabled í &K3 RTS/CTS hardware flow control enabled &K4 XON/XOFF software flow control enabled &K5 Transparent XON/XOFF software flow control enabled &K6 RTS/CTS & XON/XOFF flow control enabled GAURD TONE Type: Immediate Format: AT [cmds] &G [cmds] Description: Configures guard tone Command Function &G0 Disable guard tone &G1 Disable guard tone &G2 Set guard tone to 1800 Hz. LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line (PSTN/Dial-up) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product ID code I1 Reports ROM checksum I2 Test and reports internal memory I3 Reports firmware ID I4 Reports reserved ID SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting Extended AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function í %E0 Auto-retrain disabled %E1 Auto-retrain enabled Special Command Set ASVD/DSVD MODE Type: Configuration Format: -SMS=X,Y,Z,T [cmds] Description: Selects ASVD/DSVD mode Note: Y, Z, & T are optional parameters that control connection speed Command Function X = 0 Data mode enabled X = 1 DSVD mode enabled X = 2 ASVD mode enabled X = 3 Automatic mode select enabled ASVD MODULATION Type: Configuration Format: -SQS=X,Y [cmds] Description: Selects ASVD/DSVD mode Note: Y enables/disables ASVD automatic modulation Command Function X = 0 V.61 modulation enabled X = 1 ML144 modulation enabled X = 2 ML288 modulation enabled DSVD Type: Configuration Format: -SSE=n [cmds] Description: Enables/disables DSVD